There Are A Few Reasons That People Can Succeed In The Boarding Up A Door Industry
How to Go About Boarding Up a Door
The protection of vacant investment properties from the elements is feasible by boarding up a door. It may not prevent every damage however it can help to avoid some of the issues that are associated with severe storms.
Boarding up windows and doors can deter trespassers or vandals from entering your property. However, it can be expensive and time-consuming to install plywood boards over the openings of a property.
Take a measurement of the door
The first thing you'll need is a tape measure. It is also advisable to keep an extra chair or ladder in case you have to see more clearly at the top of the frame. Wear gloves and safety glasses if you have to make use of these tools.
Start by measuring the length of the door. You can do this by running the tape measure horizontally across the door. Make sure to remove any other parts of the door, for instance a sweep, before measuring. Next, measure the height by measuring from the floor to the sill plate or the lintel. It is crucial to measure in multiple places, particularly when measuring doors older than they may not be an exact rectangular shape. If the measurements vary then use the largest figure.
You'll have to determine the size of the frame once you've taken measurements of the height and width. Ideally, it should be 2 inches larger than the door and 1 2'' higher. This will give you plenty of space to put the door and frame to fit.
When you're ready to take the door frame's width and height measurements, it's recommended to remove any trim or casing from around the door jambs so that you can see the studs behind them. This will allow you determine the exact size of the gap between studs and the edges of the frame.
After taking off the trim, take a measurement of the width of your door frame using a tape measure. The frame should be measured at three different locations and then use the smallest measurement. Also, you should take a measurement of the height of the frame from top to bottom on both sides, and then use the shortest measurement as your door's height.
If you're having issues with these measurements, it's a good idea at this point to consult an expert and have them come out to your house to measure for you. They will tell you what dimensions and what kind of door you require and how to prepare your frame for a replacement door.
Plywood can be cut into pieces
A door frame is typically made up of a series thin boards or studs that create a hollow space surrounding the door. Two hinges are connected to the studs, and they hold the door in place. If you wish to finish doors, you'll have to remove it from its hinges over night. Placing plywood in the door's opening is an easy method to enclose the door and keep insects from getting into your home. It is simple to do without the need to screw or nail the plywood to the frame of the door.
Plywood is a breeze to work with, inexpensive and looks beautiful once completed. This makes it the perfect material for a temporary solution to an issue that requires the removal of an existing door while renovating or installing a brand new one. It can also be used to secure the opening of a room being transformed, such as an excavation site or basement.
Start by taking measurements of the width of the door opening and the height. Draw the dimensions on the plywood using the help of a utility knife, an drywall square or any other straight edge made of metal. Then, you should snap a chalk line across all the lines you have marked to indicate where you'll need to cut. Finally you can use a circular saw to cut the plywood into a size.
It is important to protect your eyes and ears when cutting plywood. Wear earplugs or goggles that are protective whenever possible. In addition, it's important to use a blade with a large number of teeth that can cut quickly and with minimal tear-out. To avoid breaking pieces of wood from the edges of the cut, use a small block of wood as template to guide the blade and keep it just a hair's width away from the line when cutting.
Attaching a pair or short braces on each side is a great way to secure the plywood in place, without screwing it into studs. Place one brace on the inside and the other on the outside of the door. Then, place a pair of 1-1/2-inch deck screws into each of the holes, and tighten them with an open-end wrench.
Fix the Plywood
Once you have a sheet of plywood cut to the right size and with the holes for the door frame's rails and stiles already drilled, it is time to secure the panel to the frame. This is a simple task that doesn't require advanced carpentry skills if you use the correct tools and follow the right steps.
Set up a table in the entrance with two sawhorses on each end, as well as framing 2x4s. Make marks during the measurement procedure to guide you in cutting the plywood. such a good point using an utility knife and a drywall square or another metal straight edge. This will serve as a guide for the saw blade, and also prevent splintering of plywood when you cut it.
Wear eye protection and cut along the scored lines with a circular saw or table saw with a fine-tooth blade. Then sand the edges of the plywood panel with 120-grit sandpaper. This will smooth out the panels and remove any burrs from the saw cuts. After sanding process, apply a coat of wood sealer to the plywood panels and let dry as directed by the manufacturer.
Install the hinges onto the door frame. If you're using a T-hinge drill holes in the outer face of your door for the straps of the hinges. Then, screw the hinge on the outside to the frame using a screwdriver. Repeat the process on the inside of the door for the hinges remaining, being cautious not to tighten too much on any of them or the panel may shift.
If you're using a single outside T-hinged door you can make it easier to lock and close with a chain lock by putting a piece of wire through the loops of the hinges outside. Bend a piece of tie wire in half and put it through the two holes on the exterior of the door. Then twist the wires to pull them tight and lock the door.
Install the Plywood
Install the plywood in the door's opening according to the measurements you took. Move the header (top) of the frame and the sill (bottom). Utilize a level to make sure there's not any slop in the header or sill. If it isn't perfect then place another shim if required and repeat the process until the sill and the header are even.
Once the plywood is in place, secure it using the stainless-steel hinge bolts and wingnuts. It's a good idea to utilize a screw gun that has an attachment for a hex-head to avoid stripping the head of the screws.
While you're there, if your house was built with studs running across the width of your doorway you can drill hanger bolts into the plywood and into each framing stud. This is much easier than using a drywall cutter to make the hole.
After putting the plywood in place, measure the width and the height of the door opening. If necessary, trim the bottom of the plywood to match the height of your door frame. Cut two pieces of framing lumber to form braces that are positioned across the upper and lower edges of your door. Wear eye protection and cut along the lines drawn on the plywood using a circular saw equipped with a fine-toothed knife. Remove any splinters from the cuts with the help of a sanding block.
After you've placed the braces after you have positioned them, use two pairs of 2-inch finishing nail to attach each brace to the plywood. When you're finished, counter sink the heads of all nails. Cover the braces using a high-quality wood sealing product, like the wipe-on polyurethane by Minwax.
If your door is too large, you can either add decorative molding to fill the space between your door and jamb, or you can resize your opening. However, in many cases, it's cheaper and more convenient to find the right door. This will also take away any issues you may have experienced with the original door if it was damaged and could no fit for the opening.